 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| SSL4101T GreenChip III+ SMPS control IC Rev. 1 -- 21 April 2011 Product data sheet 1. General description The GreenChip III+ is the third generation of green Switched Mode Power Supply (SMPS) controller ICs. The SSL4101T combines a controller for Power Factor Correction (PFC) and a flyback controller. Its high level of integration allows the design of a cost-effective LED lighting application power supply with a very low number of external components. The special built-in green functions provide high efficiency at all power levels. This applies to quasi-resonant operation at high power levels, quasi-resonant operation with valley skipping, as well as to reduced frequency operation at lower power levels. At low power levels, the PFC switches off to maintain high efficiency. During low power conditions, the flyback controller switches to frequency reduction mode and limits the peak current to 25 % of its maximum value. This will ensure high efficiency at low power and good standby power performance while minimizing audible noise from the transformer. The SSL4101T is a MultiChip Module, (MCM), containing two chips. The proprietary high voltage BCD800 process which makes direct start-up possible from the rectified universal mains voltage in an effective and green way. The second low voltage SiIlicon On Insulator (SIO) is used for accurate, high speed protection functions and control. The SSL4101T enables extremely efficient and reliable LED lighting application power supplies with power requirements from 10 W to 300 W, to be designed easily and with a minimum number of external components. The new SSL4101T allows a typical 150 W LED lighting application power supply (universal input, 48 V (DC) output, TEA1761T on the secondary side for Synchronous Rectification) to achieve the following performances at full load: * 120 V (AC): 92 % efficiency, 0.998 PF, 5.8 % THD, < 190 mW standby power * 277 V (AC): 94 % efficiency, 0.978 PF, 9 % THD, < 350 mW standby power 1.1 Industry standard THD, low standby input power and high-efficiency The SSL4101T enables LED lighting application power supplies to achieve the industry standard of < 20 % THD for the input current at full load and all nominal input voltages: 100 V (AC), 120 V (AC), 230 V (AC), 240 V (AC) and 277 V (AC). * Extremely low input power in Standby mode eliminates the need for an additional housekeeping power supply to power the lighting controllers/dimmers. NXP Semiconductors SSL4101T GreenChip III+ SMPS control IC * Using SSL4101T, a low power controller (< 50 mW) can be driven directly by the LED lighting application power supply's output while maintaining the input power in Standby mode below the maximum of 0.5 W. * Extremely high-efficiency can be achieved in LED lighting application power supplies using the SSL4101T (between 92 % to 94 %). This enables the power supply to operate reliably in enclosed spaces with very little cooling (which is typical for SSL applications). 2. Features and benefits 2.1 Distinctive features Integrated PFC and flyback controller. True universal mains supply operation: 70 V (AC) to 305 V (AC). High level of integration, resulting in a very low external component count and a cost-effective design. 2.2 Green features On-chip start-up current source. 2.3 PFC green features Valley/zero voltage switching for minimum switching losses (NXP Semiconductors patented). Frequency limitation to reduce switching losses. PFC is switched off when a low load is detected at the flyback output. 2.4 Flyback green features Valley switching for minimum switching losses (NXP Semiconductors patented). Frequency reduction with fixed minimum peak current at low power operation to maintain high efficiency at low output power levels. 2.5 Protection features Safe restart mode for system fault conditions. Continuous mode protection by means of demagnetization detection for both converters (NXP Semiconductors patented). UnderVoltage Protection (UVP) (foldback during overload). Accurate OverVoltage Protection (OVP) for both converters (adjustable for flyback converter). Open control loop protection for both converters. The open loop protection on the flyback converter is safe restart. IC OverTemperature Protection (OTP). Low and adjustable OverCurrent Protection (OCP) trip level for both converters. General purpose input for latched protection, e.g. to be used for system OverTemperature Protection (OTP). SSL4101T All information provided in this document is subject to legal disclaimers. (c) NXP B.V. 2011. All rights reserved. Product data sheet Rev. 1 -- 21 April 2011 2 of 29 NXP Semiconductors SSL4101T GreenChip III+ SMPS control IC 3. Applications The device can be used in all LED lighting applications that require a very efficient, low THD, high PF, true universal input voltage and cost-effective power supply solution between 10 W and 300 W. 4. Ordering information Table 1. Type number SSL4101T Ordering information Package Name SO16 Description plastic small outline package; 16 leads; body width 3.9 mm Version SOT109-1 5. Block diagram PFCDRIVER PFC DRIVER 1.12 V 3.5 V FBDRIVER 13 FB DRIVER DRV 80 A 12 DRV PFC GATE FB GATE LOW VIN VINSENSE 7 MAX PFCCOMP 6 LOW POWER VOSENSE 9 2.50 V 2.7 V 3.7 V 5 LATCH EXT PROT 1.25 V PFC PROT PROT ENABLE PFC R Q S Q PROT R S ENABLE FB Freq Red. LOW POWER 2.5 V 3.5 V 30 A 1.25 V PFC OSC TON MAX FB OSC Freq. Red. TIME OUT 3 FBCTRL LOW VIN VoOVP VoSTART FB VoSHORT OCP 500 mV PFC PROT VCC GOOD VoSTART FB LOW POWER EXT PROT EXT PROT OTP FBOVP LATCH RESET TIMEOUT TON MAX VoSHORT VUVLO PROT EXT PROT Vstartup Vth(UVLO) SMPS CONTROL S S LATCHED S PROTECTION R STARTFB START STOP PFC OPP FB DRIVER MIN OCP BLANK 10 FBSENSE PROT BLANK PFC DRIVER ENABLE PFC S SAFE S S RESTART PROTECTION R CHARGE CONTROL VCC GOOD CHARGE VALLEY DETECT INTERNAL SUPPLY Vstartup TIMER 50 s Vth(UVLO) 100 mV ENABLE FB START FB START SOFT 60 A PFCSENSE 11 60 A SOFT START START STOP PFC OPP COUNTER OPP OVP PFCAUX 8 VALLEY DETECT TIMER 4 s OTP PFCGATE ZCS CHARGE OvpFB 4 FBAUX FB GATE ZCS TEMP OTP 80 mV 16 HV 1 VCC 2 GND 001aan671 Remark: The time-out is safe restart for the SSL4101T. Fig 1. Block diagram SSL4101T All information provided in this document is subject to legal disclaimers. (c) NXP B.V. 2011. All rights reserved. Product data sheet Rev. 1 -- 21 April 2011 3 of 29 NXP Semiconductors SSL4101T GreenChip III+ SMPS control IC 6. Pinning information 6.1 Pinning VCC GND FBCTRL FBAUX LATCH PFCCOMP VINSENSE PFCAUX 1 2 3 4 16 HV 15 HVS 14 HVS 13 FBDRIVER SSL4101T 5 6 7 8 001aan672 12 PFCDRIVER 11 PFCSENSE 10 FBSENSE 9 VOSENSE Fig 2. Pin configuration: SSL4101T (SOT109-1) 6.2 Pin description Table 2. Symbol VCC GND FBCTRL FBAUX LATCH PFCCOMP VINSENSE PFCAUX VOSENSE FBSENSE PFCSENSE PFCDRIVER FBDRIVER HVS HV Pin description Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14, 15 16 Description supply voltage ground control input for flyback input from auxiliary winding for demagnetization timing and overvoltage protection for flyback general purpose protection input frequency compensation pin for PFC sense input for mains voltage input from auxiliary winding for demagnetization timing for PFC sense input for PFC output voltage programmable current sense input for flyback programmable current sense input for PFC gate driver output for PFC gate driver output for flyback high voltage safety spacer, not connected high voltage start-up and valley sensing of flyback part SSL4101T All information provided in this document is subject to legal disclaimers. (c) NXP B.V. 2011. All rights reserved. Product data sheet Rev. 1 -- 21 April 2011 4 of 29 NXP Semiconductors SSL4101T GreenChip III+ SMPS control IC 7. Functional description 7.1 General control The SSL4101T contains a controller for a power factor correction circuit as well as a controller for a flyback circuit. A typical configuration is shown in Figure 3. 12 8 6 11 9 16 13 10 7 3 SSL4101T 4 1 5 2 001aan673 Fig 3. Typical configuration 7.1.1 Start-up and UnderVoltage LockOut (UVLO) Initially the capacitor on the VCC pin is charged from the high voltage mains via the HV pin. As long as VCC is below Vtrip, the charge current is low. This protects the IC if the VCC pin is shorted to ground. For a short start-up time the charge current above Vtrip is increased until VCC reaches Vth(UVLO). If VCC is between Vth(UVLO) and Vstartup, the charge current is low again, ensuring a low duty cycle during fault conditions. The control logic activates the internal circuitry and switches off the HV charge current when the voltage on pin VCC passes the Vstartup level. First, the LATCH pin current source is activated and the soft start capacitors on the PFCSENSE and FBSENSE pins are charged. When the LATCH pin voltage exceeds the Ven(LATCH) voltage and the soft start capacitor on the PFCSENSE pin is charged, the PFC circuit is activated. Also the flyback converter is activated (providing the soft start capacitor on the FBSENSE pin is charged). The output voltage of the flyback converter is then regulated to its nominal output voltage. The IC supply is taken over by the auxiliary winding of the flyback converter. See Figure 4. If during start-up the LATCH pin does not reach the Ven(LATCH) level before VCC reaches Vth(UVLO), the LATCH pin output is deactivated and the charge current is switched on again. SSL4101T All information provided in this document is subject to legal disclaimers. (c) NXP B.V. 2011. All rights reserved. Product data sheet Rev. 1 -- 21 April 2011 5 of 29 NXP Semiconductors SSL4101T GreenChip III+ SMPS control IC As soon as the flyback converter is started, the voltage on the FBCTRL pin is monitored. If the output voltage of the flyback converter does not reach its intended regulation level in a predefined time, the voltage on the FBCTRL pin reaches the Vto(FBCTRL) level and an error is assumed. The SSL4101T then initiates a safe restart. When one of the protection functions is activated, both converters stop switching and the VCC voltage drops to Vth(UVLO). A latched protection recharges the capacitor CVCC via the HV pin, but does not restart the converters. For a safe restart protection, the capacitor is recharged via the HV pin and the device restarts (see block diagram, Figure 1). In the event of an overvoltage protection of the PFC circuit, VVOSENSE > Vovp(VOSENSE), only the PFC controller stops switching until the VOSENSE pin voltage drops below Vovp(VOSENSE) again. Also, if a mains undervoltage is detected VVINSENSE < Vstop(VINSENSE), only the PFC controller stops switching until VVINSENSE > Vstart(VINSENSE) again. When the voltage on pin VCC drops below the undervoltage lockout level, both controllers stop switching and reenter the safe restart mode. In the safe restart mode the driver outputs are disabled and the VCC pin voltage is recharged via the HV pin. SSL4101T All information provided in this document is subject to legal disclaimers. (c) NXP B.V. 2011. All rights reserved. Product data sheet Rev. 1 -- 21 April 2011 6 of 29 NXP Semiconductors SSL4101T GreenChip III+ SMPS control IC IHV Vstartup VCC Vth(UVLO) Vtrip Vstart(VINSENSE) VINSENSE VEN(LATCH) LATCH PROTECTION soft start PFCSENSE PFCDRIVER soft start FBSENSE FBDRIVER Vto(FBCTRL) FBCTRL Vstart(fb) VOSENSE VO charging VCC capacitor starting converters normal operation protection restart 014aaa156 Fig 4. Start-up sequence, normal operation and restart sequence 7.1.2 Supply management All internal reference voltages are derived from a temperature compensated and trimmed on-chip band gap circuit. Internal reference currents are derived from a temperature compensated and trimmed on-chip current reference circuit. 7.1.3 Latch input Pin LATCH is a general purpose input pin, which can be used to switch off both converters. The pin sources a current IO(LATCH) (80 A typical). Switching off both converters is stopped as soon as the voltage on this pin drops below 1.25 V. At initial start-up the switching is inhibited until the capacitor on the LATCH pin is charged above 1.35 V (typical). No internal filtering is done on this pin. An internal Zener clamp of 2.9 V (typical) protects this pin from excessive voltages. SSL4101T All information provided in this document is subject to legal disclaimers. (c) NXP B.V. 2011. All rights reserved. Product data sheet Rev. 1 -- 21 April 2011 7 of 29 NXP Semiconductors SSL4101T GreenChip III+ SMPS control IC 7.1.4 Fast latch reset In a typical application the mains can be interrupted briefly to reset the latched protection. The PFC bus capacitor, Cbus, does not have to discharge for this latched protection to reset. Typically the PFC bus capacitor, Cbus, has to discharge for the VCC to drop to this reset level. When the latched protection is set, the clamping circuit of the VINSENSE circuit is disabled. (see also Section 7.2.8) As soon as the VINSENSE voltage drops below 750 mV (typical) and after that is raised to 870 mV (typical), the latched protection is reset. The latched protection is also reset by removing both the voltage on pin VCC and on pin HV. 7.1.5 Overtemperature protection An accurate internal temperature protection is provided in the circuit. When the junction temperature exceeds the thermal shutdown temperature, the IC stops switching. As long as OTP is active, the capacitor CVCC is not recharged from the HV mains. The OTP circuit is supplied from the HV pin if the VCC supply voltage is not sufficient. OTP is a latched protection. It can be reset by removing both the voltage on pin VCC and on pin HV or by the fast latch reset function. (See Section 7.1.4) 7.2 Power factor correction circuit The power factor correction circuit operates in quasi-resonant or discontinuous conduction mode with valley switching. The next primary stroke is only started when the previous secondary stroke has ended and the voltage across the PFC MOSFET has reached a minimum value. The voltage on the PFCAUX pin is used to detect transformer demagnetization and the minimum voltage across the external PFC MOSFET switch. 7.2.1 ton control The power factor correction circuit is operated in ton control. The resulting mains harmonic reduction of a typical application is well within the class-D requirements. 7.2.2 Valley switching and demagnetization (PFCAUX pin) The PFC MOSFET is switched on after the transformer is demagnetized. Internal circuitry connected to the PFCAUX pin detects the end of the secondary stroke. It also detects the voltage across the PFC MOSFET. The next stroke is started when the voltage across the PFC MOSFET is at its minimum in order to reduce switching losses and ElectroMagnetic Interference (EMI) (valley switching). If no demagnetization signal is detected on the PFCAUX pin, the controller generates a zero current signal (ZCS), 50 s (typical) after the last PFCGATE signal. If no valley signal is detected on the PFCAUX pin, the controller generates a valley signal 4 s (typical) after demagnetization was detected. To protect the internal circuitry during lightning events, for example, it is advisable to add a 5 k series resistor to this pin. To prevent incorrect switching due to external disturbance, the resistor should be placed close to the IC on the printed-circuit board. SSL4101T All information provided in this document is subject to legal disclaimers. (c) NXP B.V. 2011. All rights reserved. Product data sheet Rev. 1 -- 21 April 2011 8 of 29 NXP Semiconductors SSL4101T GreenChip III+ SMPS control IC 7.2.3 Frequency limitation To optimize the transformer and minimize switching losses, the switching frequency is limited to fsw(PFC)max. If the frequency for quasi-resonant operation is above the fsw(PFC)max limit, the system switches over to discontinuous conduction mode. Also here, the PFC MOSFET is only switched on at a minimum voltage across the switch (valley switching). 7.2.4 Mains voltage compensation (VINSENSE pin) The mathematical equation for the transfer function of a power factor corrector contains the square of the mains input voltage. In a typical application this results in a low bandwidth for low mains input voltages, while at high mains input voltages the Mains Harmonic Reduction (MHR) requirements may be hard to meet. To compensate for the mains input voltage influence, the SSL4101T contains a correction circuit. Via the VINSENSE pin the average input voltage is measured and the information is fed to an internal compensation circuit. With this compensation it is possible to keep the regulation loop bandwidth constant over the full mains input range, yielding a fast transient response on load steps, while still complying with class-D MHR requirements. In a typical application, the bandwidth of the regulation loop is set by a resistor and two capacitors on the PFCCOMP pin. 7.2.5 Soft start-up (pin PFCSENSE) To prevent audible transformer noise at start-up or during hiccup, the transformer peak current, IDM, is increased slowly by the soft start function. This can be achieved by inserting RSS1 and CSS1 between pin PFCSENSE and current sense resistor RSENSE1. An internal current source charges the capacitor to VPFCSENSE = Istart(soft)PFC x RSS1. The voltage is limited to Vstart(soft)PFC. The start level and the time constant of the increasing primary current level can be adjusted externally by changing the values of RSS1 and CSS1. softstart = 3 x R SS1 x C SS1 The charging current Istart(soft)PFC flows as long as the voltage on pin PFCSENSE is below 0.5 V (typ). If the voltage on pin PFCSENSE exceeds 0.5 V, the soft start current source starts limiting current Istart(soft)PFC. As soon as the PFC starts switching, the Istart(soft)PFC current source is switched off; see Figure 5. SSL4101T All information provided in this document is subject to legal disclaimers. (c) NXP B.V. 2011. All rights reserved. Product data sheet Rev. 1 -- 21 April 2011 9 of 29 NXP Semiconductors SSL4101T GreenChip III+ SMPS control IC S1 Istartup(soft)PFC 60 A SOFT START CONTROL RSS1 11 PFCSENSE 0.5 V OCP CSS1 RSENSE1 014aaa157 Fig 5. Soft start-up of PFC 7.2.6 Low power mode When the output power of the flyback converter (see Section 7.3) is low, the flyback converter switches over to frequency reduction mode. When frequency reduction mode is entered by the flyback controller, the power factor correction circuit is switched off to maintain high efficiency. During low power mode operation the PFCCOMP pin is clamped to a minimal voltage of 2.7 V (typical) and a maximum voltage of 3.9 V (typical). The lower clamp voltage limits the maximum power that is delivered when the PFC is switched on again. The upper clamp voltage ensures that the PFC can return to its normal regulation point in a limited amount of time when returning from low power mode. As soon as the flyback converter leaves the frequency reduction mode, the power factor correction circuit restores normal operation. To prevent continuous switching on and off of the PFC circuit, a small hysteresis is build in, (60 mV (typical) on the FBCTRL pin). 7.2.7 Overcurrent protection (PFCSENSE pin) The maximum peak current is limited cycle-by-cycle by sensing the voltage across an external sense resistor, RSENSE1, on the source of the external MOSFET. The voltage is measured via the PFCSENSE pin. 7.2.8 Mains undervoltage lockout/brownout protection (VINSENSE pin) To prevent the PFC from operating at very low mains input voltages, the voltage on the VINSENSE pin is sensed continuously. As soon as the voltage on this pin drops below the Vstop(VINSENSE) level, switching of the PFC is stopped. The voltage on pin VINSENSE is clamped to a minimum value, Vstart(VINSENSE) + Vpu(VINSENSE), for a fast restart as soon as the mains input voltage is restored after a mains dropout. SSL4101T All information provided in this document is subject to legal disclaimers. (c) NXP B.V. 2011. All rights reserved. Product data sheet Rev. 1 -- 21 April 2011 10 of 29 NXP Semiconductors SSL4101T GreenChip III+ SMPS control IC 7.2.9 Overvoltage protection (VOSENSE pin) To prevent output overvoltage during load steps and mains transients, an overvoltage protection circuit is built in. As soon as the voltage on the VOSENSE pin exceeds the Vovp(VOSENSE) level, switching of the power factor correction circuit is inhibited. Switching of the PFC recommences as soon as the VOSENSE pin voltage drops below the Vovp(VOSENSE) level again. When the resistor between pin VOSENSE and ground is open, the overvoltage protection is also triggered. 7.2.10 PFC open loop protection (VOSENSE pin) The power factor correction circuit does not start switching until the voltage on the VOSENSE pin is above the Vth(ol)(VOSENSE) level. This protects the circuit from open loop and VOSENSE short situations. 7.2.11 Driver (PFCDRIVER pin) The driver circuit to the gate of the power MOSFET has a current sourcing capability of typically -500 mA and a current sink capability of typically 1.2 A. This permits fast turn-on and turn-off of the power MOSFET for efficient operation. 7.3 Flyback controller The SSL4101T includes a controller for a flyback converter. The flyback converter operates in quasi-resonant or discontinuous conduction mode with valley switching. The auxiliary winding of the flyback transformer provides demagnetization detection and powers the IC after start-up. 7.3.1 Multimode operation The SSL4101T flyback controller can operate in several modes; see Figure 6. fsw(fb)max PFC off PFC on frequency reduction switching frequency discontinuous with valley switching quasi resonant output power 014aaa158 Fig 6. Multimode operation flyback SSL4101T All information provided in this document is subject to legal disclaimers. (c) NXP B.V. 2011. All rights reserved. Product data sheet Rev. 1 -- 21 April 2011 11 of 29 NXP Semiconductors SSL4101T GreenChip III+ SMPS control IC At high output power the converter switches to quasi-resonant mode. The next converter stroke is started after demagnetization of the transformer current. In quasi-resonant mode switching losses are minimized as the converter only switches on when the voltage across the external MOSFET is at its minimum (valley switching, see also Section 7.3.2). To prevent high frequency operation at lower loads, the quasi-resonant operation changes to discontinuous mode operation with valley skipping in which the switching frequency is limited for EMI to fsw(fb)max (125 kHz typical). Again, the external MOSFET is only switched on when the voltage across the MOSFET is at its minimum. At very low power and standby levels the frequency is controlled down by a Voltage Controlled Oscillator (VCO). The minimum frequency can be reduced to zero. During frequency reduction mode, the primary peak current is kept at a minimal level of Ipkmax / 4 to maintain a high efficiency. (Ipkmax is the maximum primary peak current set by the sense resistor and the maximum sense voltage.) As the primary peak current is low in frequency reduction operation (Ipk = Ipkmax / 4), no audible noise is noticeable at switching frequencies in the audible range. Valley switching is also active in this mode. In frequency reduction mode the PFC controller is switched off and the flyback maximum frequency changes linearly with the control voltage on the FBCTRL pin (see Figure 7 ). For stable on and off switching of the PFC, the FBCTRL pin has a 50 mV (typical) hysteresis. At no load operation the switching frequency can be reduced to (almost) zero. fsw(fb)max PFC off PFC on frequency reduction switching frequency discontinuous with valley switching quasi resonant 1.5 V VFBCTRL 014aaa159 Fig 7. Frequency control of flyback part 7.3.2 Valley switching (HV pin) Refer to Figure 8. A new cycle starts when the external MOSFET is activated. After the on-time (determined by the FBSENSE voltage and the FBCTRL voltage), the MOSFET is switched off and the secondary stroke starts. After the secondary stroke, the drain voltage shows an oscillation with a frequency of approximately: 1 -------------------------------------------------( 2 x x ( Lp x Cd ) ) (1) SSL4101T All information provided in this document is subject to legal disclaimers. (c) NXP B.V. 2011. All rights reserved. Product data sheet Rev. 1 -- 21 April 2011 12 of 29 NXP Semiconductors SSL4101T GreenChip III+ SMPS control IC Where Lp is the primary self-inductance of the flyback transformer and Cd is the capacitance on the drain node. As soon as the internal oscillator voltage is high again and the secondary stroke has ended, the circuit waits for the lowest drain voltage before starting a new primary stroke. Figure 8 shows the drain voltage, valley signal, secondary stroke signal and the internal oscillator signal. Valley switching allows high frequency operation as capacitive switching losses are reduced, see Equation 2. High frequency operation makes small and cost-effective magnetics possible. P = 1 x C x V 2 x f -d 2 (2) primary stroke secondary stroke secondary ringing drain valley secondary stroke (2) (1) oscillator 014aaa027 (1) Start of new cycle at lowest drain voltage. (2) Start of new cycle in a classical Pulse Width Modulation (PWM) system without valley detection. Fig 8. Signals for valley switching 7.3.3 Current mode control (FBSENSE pin) Current mode control is used for the flyback converter for its good line regulation. The primary current is sensed by the FBSENSE pin across an external resistor and compared with an internal control voltage. The internal control voltage is proportional to the FBCTRL pin voltage, see Figure 9. SSL4101T All information provided in this document is subject to legal disclaimers. (c) NXP B.V. 2011. All rights reserved. Product data sheet Rev. 1 -- 21 April 2011 13 of 29 NXP Semiconductors SSL4101T GreenChip III+ SMPS control IC Vsense(fb)max (V) 0.52 V PFC off flyback frequency reduction flyback discontinuous or QR flyback cycle skip mode 0.13 V PFC on FBSENSE peak voltage 1.4 V 1.5 V 2.0 V VFBCTRL (V) 014aaa160 Fig 9. Peak current control of flyback part The driver output is latched in the logic, preventing multiple switch-on. 7.3.4 Demagnetization (FBAUX pin) The system is always in quasi-resonant or discontinuous conduction mode. The internal oscillator does not start a new primary stroke until the previous secondary stroke has ended. Demagnetization features a cycle-by-cycle output short circuit protection by immediately lowering the frequency (longer off-time), thereby reducing the power level. Demagnetization recognition is suppressed during the first tsup(xfmr_ring) time (2 s typical). This suppression may be necessary at low output voltages and at start-up and in applications where the transformer has a large leakage inductance. If pin FBAUX is open circuit or not connected, a fault condition is assumed and the converter stops operating immediately. Operation restarts as soon as the fault condition is removed. 7.3.5 Flyback control/time-out (FBCTRL pin) The pin FBCTRL is connected to an internal voltage source of 3.5 V via an internal resistor (typical resistance is 3 k). As soon as the voltage on this pin is above 2.5 V (typical), this connection is disabled. Above 2.5 V the pin is biased with a small current. When the voltage on this pin rises above 4.5 V (typical), a fault is assumed and switching is inhibited. In the SSL4101T, a restart will then be made. When a small capacitor is connected to this pin, a time-out function can be created to protect against an open control loop situation. (see Figure 10 and Figure 11) The time-out function can be disabled by connecting a resistor (100 k) to ground on the FBCTRL pin. If the pin is shorted to ground, switching of the flyback controller is inhibited. In normal operating conditions, when the converter is regulating the output voltage, the voltage on the FBCTRL pin is between 1.4 V and 2.0 V (typical values) from minimum to maximum output power. SSL4101T All information provided in this document is subject to legal disclaimers. (c) NXP B.V. 2011. All rights reserved. Product data sheet Rev. 1 -- 21 April 2011 14 of 29 NXP Semiconductors SSL4101T GreenChip III+ SMPS control IC 2.5 V 3.5 V 30 A 4.5 V 3 k time-out FBCTRL 014aaa049 Fig 10. Time-out protection circuit 4.5 V 2.5 V VFBCTRL output voltage intended output voltage not reached within time-out time. restart intended output voltage reached within time-out time. 014aaa050 Fig 11. Time-out protection (signals), safe restart in the SSL4101T 7.3.6 Soft start-up (FBSENSE pin) To prevent audible transformer noise during start-up, the transformer peak current, IDM is slowly increased by the soft start function. This can be achieved by inserting a resistor and a capacitor between pin 10, FBSENSE, and the current sense resistor. An internal current source charges the capacitor to V = Istart(soft)fb x RSS2, with a maximum of approximately 0.5 V. The start level and the time constant of the increasing primary current level can be adjusted externally by changing the values of RSS2 and CSS2. softstart = 3 x R SS2 x C SS2 The soft start current Istart(soft)fb is switched on as soon as VCC reaches Vstartup. When the voltage on pin FBSENSE has reached 0.5 V, the flyback converter starts switching. The charging current Istart(soft)(PFC) flows as long as the voltage on pin FBSENSE is below approximately 0.5 V. If the voltage on pin FBSENSE exceeds 0.5 V, the soft start current source starts limiting the current. After the flyback converter has started, the soft start current source is switched off. SSL4101T All information provided in this document is subject to legal disclaimers. (c) NXP B.V. 2011. All rights reserved. Product data sheet Rev. 1 -- 21 April 2011 15 of 29 NXP Semiconductors SSL4101T GreenChip III+ SMPS control IC S2 Istart(soft)fb 60 A SOFT START CONTROL RSS2 10 FBSENSE + 0.5 V OCP CSS2 RSENSE2 014aaa020 Fig 12. Soft start-up of flyback 7.3.7 Maximum on-time The flyback controller limits the `on-time' of the external MOSFET to 40 s (typical). When the `on-time' is longer than 40 s, the IC stops switching and enters the safe restart mode. 7.3.8 Overvoltage protection (FBAUX pin) An output overvoltage protection is implemented in the GreenChip III+ series. This works for the SSL4101T by sensing the auxiliary voltage via the current flowing into pin FBAUX during the secondary stroke. The auxiliary winding voltage is a well-defined replica of the output voltage. Voltage spikes are averaged by an internal filter. If the output voltage exceeds the OVP trip level, an internal counter starts counting subsequent OVP events. The counter has been added to prevent incorrect OVP detection which might occur during ESD or lightning events. If the output voltage exceeds the OVP trip level a few times and not again in a subsequent cycle, the internal counter counts down at twice the speed it uses when counting up. However, when typically eight cycles of subsequent OVP events are detected, the IC assumes a true OVP and the OVP circuit switches the power MOSFET off. As the protection is latched, the converter only restarts after the internal latch is reset. In a typical application the mains should be interrupted to reset the internal latch. The output voltage Vo(OVP) at which the OVP function trips, can be set by the demagnetization resistor, RFBAUX : Ns V O ( ovp ) = ----------- ( I ovp ( FBAUX ) x R FBAUX + V clamp ( FBAUX ) ) N aux where Ns is the number of secondary turns and Naux is the number of auxiliary turns of the transformer. Current Iovp(FBAUX) is internally trimmed. The value of RFBAUX can be adjusted to the turns ratio of the transformer, thus making an accurate OVP detection possible. SSL4101T All information provided in this document is subject to legal disclaimers. (c) NXP B.V. 2011. All rights reserved. Product data sheet Rev. 1 -- 21 April 2011 16 of 29 NXP Semiconductors SSL4101T GreenChip III+ SMPS control IC 7.3.9 Overcurrent protection (FBSENSE pin) The primary peak current in the transformer is measured accurately cycle-by-cycle using the external sense resistor Rsense2. The OCP circuit limits the voltage on pin FBSENSE to an internal level (see also Section 7.3.3). The OCP detection is suppressed during the leading edge blanking period, tleb, to prevent false triggering caused by switch-on spikes. tleb OCP level VFBSENSE t 014aaa022 Fig 13. OCP leading edge blanking 7.3.10 Overpower protection During the primary stroke of the flyback converter the input voltage of the flyback converter is measured by sensing the current that is drawn from the pin FBAUX. The current information is used to adjust the peak drain current of the flyback converter, which is measured via pin FBSENSE. The internal compensation is such that an almost input voltage independent maximum output power can be realized. The OPP curve is given in Figure 14. 0.6 VFBSENSE (V) 0.52 0.5 014aaa096 0.4 0.37 0.3 -400 -360 -300 -200 -100 0 IFBAUX (A) Fig 14. Overpower protection curve 7.3.11 Driver (FBDRIVER pin) The driver circuit to the gate of the external power MOSFET has a current sourcing capability of typically -500 mA and a current sink capability of typically 1.2 A. This permits fast turn-on and turn-off of the power MOSFET for efficient operation. SSL4101T All information provided in this document is subject to legal disclaimers. (c) NXP B.V. 2011. All rights reserved. Product data sheet Rev. 1 -- 21 April 2011 17 of 29 NXP Semiconductors SSL4101T GreenChip III+ SMPS control IC 8. Limiting values Table 3. Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Symbol Voltages VCC VLATCH VFBCTRL VPFCCOMP VVINSENSE VVOSENSE VPFCAUX VFBSENSE VPFCSENSE VHV Currents IFBCTRL IFBAUX IPFCSENSE IFBSENSE IFBDRIVER IPFCDRIVER IHV General Ptot Tstg Tj ESD VESD electrostatic discharge voltage class 1 human body model pins 1 to 13 pin 16 (HV) machine model charged device model [1] [2] Equivalent to discharging a 100 pF capacitor through a 1.5 k series resistor. Equivalent to discharging a 200 pF capacitor through a 0.75 H coil and a 10 resistor. [1] [1] [2] Parameter supply voltage voltage on pin LATCH voltage on pin FBCTRL voltage on pin PFCCOMP voltage on pin VINSENSE voltage on pin VOSENSE voltage on pin PFCAUX voltage on pin FBSENSE voltage on pin PFCSENSE voltage on pin HV current on pin FBCTRL current on pin FBAUX current on pin PFCSENSE current on pin FBSENSE current on pin FBDRIVER current on pin PFCDRIVER current on pin HV total power dissipation storage temperature junction temperature Conditions Min -0.4 Max +38 +5 +5 +5 +5 +5 +25 +5 +5 +650 0 +1 +10 +10 +2 +2 5 0.6 +150 +150 Unit V V V V V V V V V V mA mA mA mA A A mA W C C current limited -0.4 -0.4 -0.4 -0.4 -0.4 -25 current limited current limited -0.4 -0.4 -0.4 -3 -1 -1 -1 duty cycle < 10 % duty cycle < 10 % -0.8 -0.8 - Tamb < 75 C -55 -40 - 2000 1500 200 500 V V V V SSL4101T All information provided in this document is subject to legal disclaimers. (c) NXP B.V. 2011. All rights reserved. Product data sheet Rev. 1 -- 21 April 2011 18 of 29 NXP Semiconductors SSL4101T GreenChip III+ SMPS control IC 9. Thermal characteristics Table 4. Symbol Rth(j-a) Thermal characteristics Parameter thermal resistance from junction to ambient Conditions in free air; JEDEC test board Typ 124 Unit K/W 10. Characteristics Table 5. Characteristics Tamb = 25 C; VCC = 20 V; all voltages are measured with respect to ground (pin 2); currents are positive when flowing into the IC; unless otherwise specified. Symbol IHV Parameter current on pin HV Conditions VHV > 80 V VCC < Vtrip; Vth(UVLO) < VCC < Vstartup Vtrip < VCC < Vth(UVLO) with auxiliary supply VBR Vtrip Vstartup Vth(UVLO) Vstart(hys) Vhys Ich(low) Ich(high) ICC(oper) breakdown voltage trip voltage start-up voltage undervoltage lockout threshold voltage hysteresis of start voltage hysteresis voltage low charging current high charging current operating supply current during start-up phase Vstartup - Vth(UVLO) VHV > 80 V; VCC < Vtrip or Vth(UVLO) < VCC < Vstartup VHV > 80 V; Vtrip < VCC < Vth(UVLO) no load on pin FBDRIVER and PFCDRIVER Supply voltage management (pin VCC) 0.55 21 14 6.3 -1.2 -4.6 2.25 0.65 22 15 300 7 -1.0 -5.4 3 0.75 23 16 7.7 -0.8 -6.3 3.75 V V V mV V mA mA mA 8 650 1.0 5.4 20 40 mA mA A V Min Typ Max Unit Start-up current source (pin HV) Input voltage sensing PFC (pin VINSENSE) Vstop(VINSENSE) Vstart(VINSENSE) Vpu(VINSENSE) Ipu(VINSENSE) stop voltage on pin VINSENSE start voltage on pin VINSENSE pull-up voltage difference on pin VINSENSE pull-up current on pin VINSENSE active after Vstop(VINSENSE) is detected active after Vstop(VINSENSE) is detected 0.86 1.11 -55 4.0 0.89 1.15 -100 -47 0.92 1.19 -40 V V mV A V Vmvc(VINSENSE)max maximum mains voltage compensation voltage on pin VINSENSE Vflr Vflr(hys) II(VINSENSE) fast latch reset voltage hysteresis of fast latch reset voltage input current on pin VINSENSE VVINSENSE > Vstop(VINSENSE) after Vstart(VINSENSE) is detected All information provided in this document is subject to legal disclaimers. active after Vth(UVLO) is detected 5 0.75 0.12 33 100 V V nA SSL4101T (c) NXP B.V. 2011. All rights reserved. Product data sheet Rev. 1 -- 21 April 2011 19 of 29 NXP Semiconductors SSL4101T GreenChip III+ SMPS control IC Table 5. Characteristics ...continued Tamb = 25 C; VCC = 20 V; all voltages are measured with respect to ground (pin 2); currents are positive when flowing into the IC; unless otherwise specified. Symbol gm IO(PFCCOMP) Vclamp(PFCCOMP) Parameter transconductance output current on pin PFCCOMP clamp voltage on pin PFCCOMP zero on-time voltage on pin PFCCOMP maximum on-time voltage on pin PFCCOMP PFC on-time VVINSENSE = 3.3 V; VPFCCOMP = Vton(PFCCOMP)max VVINSENSE = 1 V; VPFCCOMP = Vton(PFCCOMP)max Output voltage sensing PFC (pin VOSENSE) Vth(ol)(VOSENSE) Vreg(VOSENSE) Vovp(VOSENSE) Iprot(VOSENSE) open-loop threshold voltage on pin VOSENSE regulation voltage on pin VOSENSE overvoltage protection voltage on pin VOSENSE protection current on pin VOSENSE maximum PFC sense voltage PFC leading edge blanking time protection current on pin PFCSENSE PFC soft start current PFC soft start voltage PFC soft start resistance maximum PFC switching frequency minimum PFC off-time enabling voltage V/t = 50 mV/s V/t = 200 mV/s tleb(PFC) Iprot(PFCSENSE) for IO(PFCCOMP) = 0 A 0.4 V Conditions VVOSENSE to IO(PFCCOMP) VVOSENSE = 3.3 V VVOSENSE = 2.0 V Low power mode; PFC off; lower clamp voltage Upper clamp voltage Vton(PFCCOMP)zero Vton(PFCCOMP)max [1] Min 60 33 -45 2.5 3.4 1.20 Typ 80 39 -39 2.7 3.9 3.5 1.25 Max 100 45 -33 2.9 3.6 1.30 Unit A/V A A V V V V Loop compensation PFC (pin PFCCOMP) [1] Pulse width modulator PFC ton(PFC) 3.6 30 4.5 40 5 53 s s 2.475 2.500 2.525 V 2.60 2.63 -30 2.67 V nA Overcurrent protection PFC (pin PFCSENSE) Vsense(PFC)max 0.49 0.52 250 -50 0.52 0.55 310 0.55 0.57 370 -5 V V ns nA Soft start PFC (pin PFCSENSE) Istart(soft)PFC Vstart(soft)PFC Rstart(soft)PFC Oscillator PFC fsw(PFC)max toff(PFC)min 300 0.8 380 1.1 460 1.4 kHz s -75 0.46 12 -60 0.50 -45 0.54 A V k SSL4101T All information provided in this document is subject to legal disclaimers. (c) NXP B.V. 2011. All rights reserved. Product data sheet Rev. 1 -- 21 April 2011 20 of 29 NXP Semiconductors SSL4101T GreenChip III+ SMPS control IC Table 5. Characteristics ...continued Tamb = 25 C; VCC = 20 V; all voltages are measured with respect to ground (pin 2); currents are positive when flowing into the IC; unless otherwise specified. Symbol (V/t)vrec(PFC) tvrec(PFC) tto(vrec)PFC Parameter PFC valley recognition voltage change with time PFC valley recognition time PFC valley recognition time-out time comparator threshold voltage on pin PFCAUX PFC demagnetization time-out time protection current on pin PFCAUX source current on pin PFCDRIVER sink current on pin PFCDRIVER maximum output voltage on pin PFCDRIVER overvoltage protection current on pin FBAUX number of overvoltage protection cycles comparator threshold voltage on pin FBAUX protection current on pin FBAUX clamp voltage on pin FBAUX transformer ringing suppression time minimum flyback on-time maximum flyback on-time VFBAUX = 50 mV IFBAUX = -500 A IFBAUX = 500 A tsup(xfmr_ring) VPFCAUX = 50 mV VPFCAUX = 1 V peak-to-peak demagnetization to V/t = 0 [2] [3] Conditions Min 3 Typ 4 Max 1.7 300 50 6 Unit V/s ns ns s Valley switching PFC (pin PFCAUX) Demagnetization management PFC (pin PFCAUX) Vth(comp)PFCAUX tto(demag)PFC Iprot(PFCAUX) -150 40 -75 -100 50 -50 60 -5 mV s nA Driver (pin PFCDRIVER) Isrc(PFCDRIVER) Isink(PFCDRIVER) VO(PFCDRIVER)max VPFCDRIVER = 2 V VPFCDRIVER = 2 V VPFCDRIVER = 10 V -0.5 0.7 1.2 11 12 A A A V Overvoltage protection flyback (pin FBAUX) Iovp(FBAUX) Ncy(ovp) 279 6 300 8 321 12 A Demagnetization management flyback (pin FBAUX) Vth(comp)FBAUX Iprot(FBAUX) Vclamp(FBAUX) 60 -50 -1.0 0.5 1.5 80 -0.8 0.7 2 110 -5 -0.6 0.9 2.5 mV nA V V s Pulse width modulator flyback ton(fb)min ton(fb)max 32 tleb 40 48 ns s SSL4101T All information provided in this document is subject to legal disclaimers. (c) NXP B.V. 2011. All rights reserved. Product data sheet Rev. 1 -- 21 April 2011 21 of 29 NXP Semiconductors SSL4101T GreenChip III+ SMPS control IC Table 5. Characteristics ...continued Tamb = 25 C; VCC = 20 V; all voltages are measured with respect to ground (pin 2); currents are positive when flowing into the IC; unless otherwise specified. Symbol Oscillator flyback fsw(fb)max Vstart(VCO)FBCTRL Vhys(FBCTRL) VVCO(FBCTRL) maximum flyback switching frequency VCO start voltage on pin FBCTRL hysteresis voltage on pin FBCTRL VCO voltage difference on pin FBCTRL voltage on pin FBCTRL time-out voltage on pin FBCTRL internal resistance on pin FBCTRL output current on pin FBCTRL time-out current on pin FBCTRL VFBCTRL = 0 V VFBCTRL = 2 V Ito(FBCTRL) VFBCTRL = 2.6 V VFBCTRL = 4.1 V for maximum flyback peak current enable voltage trip voltage [4] Parameter Conditions Min 100 1.3 - Typ 125 1.5 60 -0.1 Max 150 1.7 - Unit kHz V mV V Peak current control flyback (pin FBCTRL) VFBCTRL Vto(FBCTRL) Rint(FBCTRL) IO(FBCTRL) 1.85 4.2 -1.4 -0.6 -36 2.0 2.5 4.5 3 2.15 4.8 V V V k -1.19 -0.93 mA -0.5 -30 -0.4 -24 mA A -34.5 -28.5 -22.5 A -75 [5] Valley switching flyback (pin HV) (V/t)vrec(fb) td(vrec-swon) flyback valley recognition voltage change with time valley recognition to switch-on delay time flyback soft start current flyback soft start voltage flyback soft start resistance maximum flyback sense voltage flyback leading edge blanking time OPP start current on pin FBAUX reduced overpower protection current on pin FBAUX Vsense(fb)max has reduced to 0.37 V V/t = 50 mV/s V/t = 200 mV/s enable voltage 150 +75 V/s ns - Soft start flyback (pin FBSENSE) Istart(soft)fb Vstart(soft)fb Rstart(soft)fb Vsense(fb)max tleb(fb) Istart(OPP)FBAUX Iopp(red)(FBAUX) -75 0.43 12 0.49 0.52 255 -60 0.49 0.52 0.55 305 -100 -360 -45 0.54 0.55 0.58 355 A V k V V ns A A Overcurrent protection flyback (pin FBSENSE) SSL4101T All information provided in this document is subject to legal disclaimers. (c) NXP B.V. 2011. All rights reserved. Product data sheet Rev. 1 -- 21 April 2011 22 of 29 NXP Semiconductors SSL4101T GreenChip III+ SMPS control IC Table 5. Characteristics ...continued Tamb = 25 C; VCC = 20 V; all voltages are measured with respect to ground (pin 2); currents are positive when flowing into the IC; unless otherwise specified. Symbol Isrc(FBDRIVER) Isink(FBDRIVER) VO(FBDRIVER)(max) Parameter source current on pin FBDRIVER sink current on pin FBDRIVER maximum output voltage on pin FBDRIVER protection voltage on pin LATCH output current on pin LATCH enable voltage on pin LATCH hysteresis voltage on pin LATCH open-circuit voltage on pin LATCH IC protection level temperature hysteresis of IC protection level temperature Vprot(LATCH) < VLATCH < Voc(LATCH) at start-up Ven(LATCH) - Vprot(LATCH) Conditions VFBDRIVER = 2 V VFBDRIVER = 2 V VFBDRIVER = 10 V Min Typ -0.5 0.7 1.2 11 Max 12 Unit A A A V Driver (pin FBDRIVER) LATCH input (pin LATCH) Vprot(LATCH) IO(LATCH) Ven(LATCH) Vhys(LATCH) Voc(LATCH) 1.23 -85 1.30 80 2.65 1.25 -80 1.35 100 2.9 1.27 -75 1.40 140 3.15 V A V mV V Temperature protection Tpl(IC) Tpl(IC)hys 130 140 10 150 C C [1] [2] [3] [4] [5] For a typical application with a compensation network on pin PFCCOMP, such as the example shown in Figure 3. Minimum required voltage change time for valley recognition on pin PFCAUX. Minimum time required between demagnetization detection and V/t = 0 on pin PFCAUX. Hysteresis for PFC on/off control. Guaranteed by design. SSL4101T All information provided in this document is subject to legal disclaimers. (c) NXP B.V. 2011. All rights reserved. Product data sheet Rev. 1 -- 21 April 2011 23 of 29 NXP Semiconductors SSL4101T GreenChip III+ SMPS control IC 11. Application information A power supply with the SSL4101T consists of a power factor correction circuit followed by a flyback converter. See Figure 14. Capacitor CVCC buffers the IC supply voltage, which is powered via the high voltage rectified mains during start-up and via the auxiliary winding of the flyback converter during operation. Sense resistors RSENSE1 and RSENSE2 convert the current through the MOSFETs S1 and S2 into a voltage at pins PFCSENSE and FBSENSE. The values of RSENSE1 and RSENSE2 define the maximum primary peak current in MOSFETs S1 and S2. In the example given, the LATCH pin is connected to a Negative Temperature Coefficient (NTC) resistor. When the resistance drops below Equation 3 (typ), the protection is activated. V prot ( LATCH ) ------------------------------- = 15.6 k I O ( LATCH ) (3) A capacitor CTIMEOUT is connected to the FBCTRL pin. For a 120 nF capacitor, typically after 10 ms the time-out protection is activated. RLOOP is added so that the time-out capacitor does not interfere with the normal regulation loop. RS1 and RS2 are added to prevent the soft start capacitors from being charged during normal operation due to negative voltage spikes across the sense resistors. Resistor RAUX1 is added to protect the IC from damage during lightning events. D1 Cbus S1 CSS1 RSS1 T2 RSENSE1 D2 COUT RAUX1 RS1 S2 COMPENSATION 12 8 6 11 9 16 13 10 RS2 RSS2 SSL4101T 7 4 1 3 2 5 CSS2 RSENSE2 RAUX2 CVCC RLOOP CTIMEOUT 014aaa302 Fig 15. Typical application diagram SSL4101T SSL4101T All information provided in this document is subject to legal disclaimers. (c) NXP B.V. 2011. All rights reserved. Product data sheet Rev. 1 -- 21 April 2011 24 of 29 NXP Semiconductors SSL4101T GreenChip III+ SMPS control IC 12. Package outline SO16: plastic small outline package; 16 leads; body width 3.9 mm SOT109-1 D E A X c y HE vMA Z 16 9 Q A2 pin 1 index Lp 1 8 A1 (A 3) A L wM detail X e bp 0 2.5 scale 5 mm DIMENSIONS (inch dimensions are derived from the original mm dimensions) UNIT mm inches A max. 1.75 A1 0.25 0.10 A2 1.45 1.25 A3 0.25 0.01 bp 0.49 0.36 c 0.25 0.19 D (1) 10.0 9.8 E (1) 4.0 3.8 0.16 0.15 e 1.27 0.05 HE 6.2 5.8 L 1.05 Lp 1.0 0.4 0.039 0.016 Q 0.7 0.6 0.028 0.020 v 0.25 0.01 w 0.25 0.01 y 0.1 Z (1) 0.7 0.3 o 0.010 0.057 0.069 0.004 0.049 0.019 0.0100 0.39 0.014 0.0075 0.38 0.244 0.041 0.228 0.028 0.004 0.012 8 o 0 Note 1. Plastic or metal protrusions of 0.15 mm (0.006 inch) maximum per side are not included. OUTLINE VERSION SOT109-1 REFERENCES IEC 076E07 JEDEC MS-012 JEITA EUROPEAN PROJECTION ISSUE DATE 99-12-27 03-02-19 Fig 16. Package outline SOT109-1 (SO16) SSL4101T All information provided in this document is subject to legal disclaimers. (c) NXP B.V. 2011. All rights reserved. Product data sheet Rev. 1 -- 21 April 2011 25 of 29 NXP Semiconductors SSL4101T GreenChip III+ SMPS control IC 13. Revision history Table 6. Revision history Release date 20110421 Data sheet status Product data sheet Change notice Supersedes Document ID SSL4101T v.1 SSL4101T All information provided in this document is subject to legal disclaimers. (c) NXP B.V. 2011. All rights reserved. Product data sheet Rev. 1 -- 21 April 2011 26 of 29 NXP Semiconductors SSL4101T GreenChip III+ SMPS control IC 14. Legal information 14.1 Data sheet status Document status[1][2] Objective [short] data sheet Preliminary [short] data sheet Product [short] data sheet [1] [2] [3] Product status[3] Development Qualification Production Definition This document contains data from the objective specification for product development. This document contains data from the preliminary specification. This document contains the product specification. Please consult the most recently issued document before initiating or completing a design. The term `short data sheet' is explained in section "Definitions". The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the Internet at URL http://www.nxp.com. 14.2 Definitions Draft -- The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. NXP Semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. Short data sheet -- A short data sheet is an extract from a full data sheet with the same product type number(s) and title. A short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. For detailed and full information see the relevant full data sheet, which is available on request via the local NXP Semiconductors sales office. In case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail. Product specification -- The information and data provided in a Product data sheet shall define the specification of the product as agreed between NXP Semiconductors and its customer, unless NXP Semiconductors and customer have explicitly agreed otherwise in writing. In no event however, shall an agreement be valid in which the NXP Semiconductors product is deemed to offer functions and qualities beyond those described in the Product data sheet. malfunction of an NXP Semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. NXP Semiconductors accepts no liability for inclusion and/or use of NXP Semiconductors products in such equipment or applications and therefore such inclusion and/or use is at the customer's own risk. Applications -- Applications that are described herein for any of these products are for illustrative purposes only. NXP Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Customers are responsible for the design and operation of their applications and products using NXP Semiconductors products, and NXP Semiconductors accepts no liability for any assistance with applications or customer product design. It is customer's sole responsibility to determine whether the NXP Semiconductors product is suitable and fit for the customer's applications and products planned, as well as for the planned application and use of customer's third party customer(s). Customers should provide appropriate design and operating safeguards to minimize the risks associated with their applications and products. NXP Semiconductors does not accept any liability related to any default, damage, costs or problem which is based on any weakness or default in the customer's applications or products, or the application or use by customer's third party customer(s). Customer is responsible for doing all necessary testing for the customer's applications and products using NXP Semiconductors products in order to avoid a default of the applications and the products or of the application or use by customer's third party customer(s). NXP does not accept any liability in this respect. Limiting values -- Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) will cause permanent damage to the device. Limiting values are stress ratings only and (proper) operation of the device at these or any other conditions above those given in the Recommended operating conditions section (if present) or the Characteristics sections of this document is not warranted. Constant or repeated exposure to limiting values will permanently and irreversibly affect the quality and reliability of the device. Terms and conditions of commercial sale -- NXP Semiconductors products are sold subject to the general terms and conditions of commercial sale, as published at http://www.nxp.com/profile/terms, unless otherwise agreed in a valid written individual agreement. In case an individual agreement is concluded only the terms and conditions of the respective agreement shall apply. NXP Semiconductors hereby expressly objects to applying the customer's general terms and conditions with regard to the purchase of NXP Semiconductors products by customer. No offer to sell or license -- Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights. Export control -- This document as well as the item(s) described herein may be subject to export control regulations. Export might require a prior authorization from national authorities. (c) NXP B.V. 2011. All rights reserved. 14.3 Disclaimers Limited warranty and liability -- Information in this document is believed to be accurate and reliable. However, NXP Semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. In no event shall NXP Semiconductors be liable for any indirect, incidental, punitive, special or consequential damages (including - without limitation - lost profits, lost savings, business interruption, costs related to the removal or replacement of any products or rework charges) whether or not such damages are based on tort (including negligence), warranty, breach of contract or any other legal theory. Notwithstanding any damages that customer might incur for any reason whatsoever, NXP Semiconductors' aggregate and cumulative liability towards customer for the products described herein shall be limited in accordance with the Terms and conditions of commercial sale of NXP Semiconductors. Right to make changes -- NXP Semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. Suitability for use -- NXP Semiconductors products are not designed, authorized or warranted to be suitable for use in life support, life-critical or safety-critical systems or equipment, nor in applications where failure or SSL4101T All information provided in this document is subject to legal disclaimers. Product data sheet Rev. 1 -- 21 April 2011 27 of 29 NXP Semiconductors SSL4101T GreenChip III+ SMPS control IC whenever customer uses the product for automotive applications beyond NXP Semiconductors' specifications such use shall be solely at customer's own risk, and (c) customer fully indemnifies NXP Semiconductors for any liability, damages or failed product claims resulting from customer design and use of the product for automotive applications beyond NXP Semiconductors' standard warranty and NXP Semiconductors' product specifications. Quick reference data -- The Quick reference data is an extract of the product data given in the Limiting values and Characteristics sections of this document, and as such is not complete, exhaustive or legally binding. Non-automotive qualified products -- Unless this data sheet expressly states that this specific NXP Semiconductors product is automotive qualified, the product is not suitable for automotive use. It is neither qualified nor tested in accordance with automotive testing or application requirements. NXP Semiconductors accepts no liability for inclusion and/or use of non-automotive qualified products in automotive equipment or applications. In the event that customer uses the product for design-in and use in automotive applications to automotive specifications and standards, customer (a) shall use the product without NXP Semiconductors' warranty of the product for such automotive applications, use and specifications, and (b) 14.4 Trademarks Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners. GreenChip -- is a trademark of NXP B.V. 15. Contact information For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com SSL4101T All information provided in this document is subject to legal disclaimers. (c) NXP B.V. 2011. All rights reserved. Product data sheet Rev. 1 -- 21 April 2011 28 of 29 NXP Semiconductors SSL4101T GreenChip III+ SMPS control IC 16. Contents 1 1.1 2 2.1 2.2 2.3 2.4 2.5 3 4 5 6 6.1 6.2 7 7.1 7.1.1 7.1.2 7.1.3 7.1.4 7.1.5 7.2 7.2.1 7.2.2 7.2.3 7.2.4 7.2.5 7.2.6 7.2.7 7.2.8 7.2.9 7.2.10 7.2.11 7.3 7.3.1 7.3.2 General description . . . . . . . . . . . . . . . . . . . . . . 1 Industry standard THD, low standby input power and high-efficiency . . . . . . . . . . . . . . . . . 1 Features and benefits . . . . . . . . . . . . . . . . . . . . 2 Distinctive features . . . . . . . . . . . . . . . . . . . . . . 2 Green features . . . . . . . . . . . . . . . . . . . . . . . . . 2 PFC green features . . . . . . . . . . . . . . . . . . . . . 2 Flyback green features . . . . . . . . . . . . . . . . . . . 2 Protection features . . . . . . . . . . . . . . . . . . . . . . 2 Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Ordering information . . . . . . . . . . . . . . . . . . . . . 3 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Pinning information . . . . . . . . . . . . . . . . . . . . . . 4 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 4 Functional description . . . . . . . . . . . . . . . . . . . 5 General control . . . . . . . . . . . . . . . . . . . . . . . . . 5 Start-up and UnderVoltage LockOut (UVLO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Supply management. . . . . . . . . . . . . . . . . . . . . 7 Latch input . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Fast latch reset . . . . . . . . . . . . . . . . . . . . . . . . . 8 Overtemperature protection . . . . . . . . . . . . . . . 8 Power factor correction circuit . . . . . . . . . . . . . 8 ton control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Valley switching and demagnetization (PFCAUX pin) . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Frequency limitation . . . . . . . . . . . . . . . . . . . . . 9 Mains voltage compensation (VINSENSE pin) . . . . . . . . . . . . . . . . . . . . . . . . 9 Soft start-up (pin PFCSENSE) . . . . . . . . . . . . . . . . . . . . . . . 9 Low power mode . . . . . . . . . . . . . . . . . . . . . . 10 Overcurrent protection (PFCSENSE pin) . . . . . . . . . . . . . . . . . . . . . . 10 Mains undervoltage lockout/brownout protection (VINSENSE pin) . . . . . . . . . . . . . . 10 Overvoltage protection (VOSENSE pin) . . . . . . . . . . . . . . . . . . . . . . . 11 PFC open loop protection (VOSENSE pin) . . . . . . . . . . . . . . . . . . . . . . . 11 Driver (PFCDRIVER pin) . . . . . . . . . . . . . . . . . . . . . . 11 Flyback controller . . . . . . . . . . . . . . . . . . . . . . 11 Multimode operation . . . . . . . . . . . . . . . . . . . . 11 Valley switching (HV pin) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 7.3.3 7.3.4 7.3.5 7.3.6 7.3.7 7.3.8 7.3.9 7.3.10 7.3.11 8 9 10 11 12 13 14 14.1 14.2 14.3 14.4 15 16 Current mode control (FBSENSE pin) . . . . . . . . . . . . . . . . . . . . . . . Demagnetization (FBAUX pin). . . . . . . . . . . . . . . . . . . . . . . . . . Flyback control/time-out (FBCTRL pin). . . . . . . . . . . . . . . . . . . . . . . . . Soft start-up (FBSENSE pin) . . . . . . . . . . . . . . . . . . . . . . . Maximum on-time . . . . . . . . . . . . . . . . . . . . . Overvoltage protection (FBAUX pin). . . . . . . . . . . . . . . . . . . . . . . . . . Overcurrent protection (FBSENSE pin) . . . . . . . . . . . . . . . . . . . . . . . Overpower protection. . . . . . . . . . . . . . . . . . . Driver (FBDRIVER pin). . . . . . . . . . . . . . . . . . . . . . . Limiting values . . . . . . . . . . . . . . . . . . . . . . . . Thermal characteristics . . . . . . . . . . . . . . . . . Characteristics . . . . . . . . . . . . . . . . . . . . . . . . Application information . . . . . . . . . . . . . . . . . Package outline. . . . . . . . . . . . . . . . . . . . . . . . Revision history . . . . . . . . . . . . . . . . . . . . . . . Legal information . . . . . . . . . . . . . . . . . . . . . . Data sheet status . . . . . . . . . . . . . . . . . . . . . . Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . Contact information . . . . . . . . . . . . . . . . . . . . Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 14 14 15 16 16 17 17 17 18 19 19 24 25 26 27 27 27 27 28 28 29 Please be aware that important notices concerning this document and the product(s) described herein, have been included in section `Legal information'. (c) NXP B.V. 2011. All rights reserved. For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com Date of release: 21 April 2011 Document identifier: SSL4101T |
Price & Availability of SSL4101T
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |